This is default featured slide 1 title
This is default featured slide 2 title
This is default featured slide 3 title
This is default featured slide 4 title
This is default featured slide 5 title

Monthly Archives: October 2017

Prepare Home For Winter

Clear Your Eaves
This is not a complicated task, but it’s an important job nonetheless. Clogged eavestroughs can lead to the formation of ice dams, which can tear off gutters, loosen shingles and leave your roof vulnerable to leaks. Simply climb to the edge of your roof and carefully dig out the debris. It’s not necessary to remove every small stone. The main purpose is to make sure nothing restricts the flow of water, and that no stagnant water remains in the gutters.

Prevent Ice Dams
If your home had lots of icicles last winter, or worse, ice dams, which can cause meltwater to back up and flow into your house, take steps to prevent potential damage this year. Get the assistance of a home-energy auditor or weatherization contractor. Have them fix the air leaks or inadequate insulation in your attic.

Check Your Roof
If you can’t get access to your roof, or prefer not to go on the roof, use binoculars to inspect the shingles. Look for damaged, loose or missing shingles that may leak during winter’s storms or from melting snow.

Caulk Windows and Doors
If the gaps between siding and window or door frames are bigger than the width of a nickel, you need to reapply exterior caulk. (Check the joints in window and door frames, too.) Silicone caulk is best for exterior use because it won’t shrink and it’s impervious to the elements.

Shut Off Exterior Faucets
Cold winter temperatures can cause your pipes to freeze and burst inside your home, which can result in major water damage. Locate and close any shut-off valves that lead to outside faucets, and drain any excess water inside the lines. It’s also a good idea to also drain any interior pipes in unheated areas of your home, such as your attic.

Stow Your Mower
As the mower sits through the winter, fuel remaining in its engine will decompose, “varnishing” the carburetor and causing difficulty when you try to start the engine in the spring. wait until the tank is nearly empty from use and run the engine (outdoors) to use up the remaining fuel.

Call a Chimney Sweep
Before you burn the Yule log, make sure your fireplace (or any heating appliance burning gas, oil, wood or coal), chimney and vents are clean and in good repair. That will prevent chimney fires and prevent carbon monoxide from creeping into your home. If you have a wood-burning heating appliance or fireplace, have your chimney inspected and cleaned by a certified chimney inspector to reduce your risk of a fire.

Repair for All Types of Water Damage

Types of Damage Based on Category

Clean water damage occurs when the water is clear and does not contain contaminants. In this case, the water usually comes from a burst pipe. Even though the health hazard for people is practically non-existent, you must act immediately to dry the flooded area or mold can grow quickly.

Grey water is an indicator of slight contamination with microbes. It may come from the washing machine or from the toilet bowl. Cleaning should begin immediately provided that cleaners wear protective gloves, masks and goggles.

Black water is heavily contaminated by all kinds of dangerous microorganisms and possibly chemicals such as fertilizers and pesticides. Black water flooding usually occurs in case of a natural disaster or serious damage to the sewage system. This type of water damage must be handled by professionals only as it is extremely hazardous.

Levels of Water Damage

Class 1 destruction is when there is a small amount of moisture within a restricted area. Usually, only porous materials such as plywood are affected. As long as the area is dried quickly, only minor water damage repair will be necessary.

Class 2 destruction is present when the water has affected the entire room and has reached a level of twelve inches or higher. It has penetrated various structural materials, but not too deeply. In this case, the repair can involve removing wet sections of damaged materials like drywall and filling the holes with special sealant. This method has the best chances of working when the drying is quick.

Class 3 water destruction is when the walls, ceilings and floors along with the carpet and insulation are saturated with water. Professional inspection is necessary to determine if the house can be salvaged, which is most often the case, what kind of repair is needed and how much it will cost. The solution typically involves replacing the flooring, the wall and ceiling drywall panels and the insulation.

Class 4 destruction is when the water has saturated even non-porous materials such as stone. The most serious type of water damage typically occurs when the house has not been dried quickly. It is worth noting that sometimes the delay is due to technical reasons such as uncertainty whether the structure is safe enough for the restoration crew to get in. Again, expert inspection is required for determining if and how the house can be saved. If the foundation is mostly still intact, for example, repair may be an effective solution.

Benefits Of Weathering Steels

Exposure to the elements

Traditional steel loses its strength when exposed to corrosion, but Corten gets stronger when it is exposed to the weather. The sheets form a layer of beneficial layer when they come into contact with oxygen and moisture. So, this is one of the major benefits of Corten.

The strength of the weathering steel is also very high. Plus, they require less maintenance and save you a lot of money. All of these benefits make this type of steel an ideal choice for the construction of roofs, bridges and buildings with open frames. As a matter fact, history tells us that bridges constructed with the weathering steel stand the test of time for as many as 120 years without requiring a lot of maintenance. So, these bridges don’t need to be regularly checked or inspected.

The look of the Corten is another thing that makes it so popular. Buildings constructed with this steel look reddish, just like rust. As the exposure to the elements continues, the steel starts to have a russet patina, and most people find it very beautiful. So, the rust looks beautiful and doesn’t look ugly in any way.

The Takeaway

To cut a long story short, Corten steel is popular among a large community of engineers and architects. And the reason is that it offers a lot of advantages over the traditional steel. This steel is arguably the strongest steel that is able to stand the test of time and doesn’t require a lot of regular upkeep. Moreover, buildings built with the Corten don’t need to be painted, which is a great thing for the environment as well. And the biggest of the benefits is that you save a lot of bucks, as you don’t need to pay to the professional to inspect the buildings on a regular basis.

Having Aluminium Curtain Walling

Lighting and elegance

The combination of aluminium frames and glass material together makes it a very classy option to use, also allows the abundance of daylight to walk in, thus leading to less use of power consumption during the daytime.

No UV rays

UV – the ultraviolet rays are very harmful to any skin, as they can cause severe disease in long run. It is necessary to opt for a material that is very friendly in terms of harmful rays. The design of the wall confirms the 99% reduction of harmful and toxic UV rays to the human bodies.

Wind resistant

The structure of the wall is very efficient in keeping away the wind and forces that are acting against the building.

Fire extinguisher

The design of the wall is very helpful in preventing the fire from spreading floor to floor.

Disadvantages of curtain walls

Great Cost and time

These walls are very ineffective in terms of cost and time management. The Huge cost is involved while shipping the material and storing them. The time taken to complete the structure is very long too.

Replacement of sealant

To keep the wind and moisture at vicinity, a sealant is applied to the perimeter of the structure. The sealant needs to be replaced after every 10 years or so.

Peculiar Cleaning

These walls require huge cleaning and maintenance on an everyday basis. As aluminium frames are generally painted or are anodized. It is necessary to make sure that the cleaning near the anodized parts is done very carefully, as cleaning supplies or detergent can clear off the coating from such frames or material.